* tests/Makefile.am (run-threaded): Add.
* tests/run-threaded.c: New.
--
This test is intended to help detect race conditions
or other multithread problems. It can also be used
to put the whole GnuPG system under extreme load.
* tests/gpg/t-support.h (check_gpg_version, compare_versions),
(parse_version_string, parse_version_number): Remove version
check code.
* tests/json/t-json.c (check_gpg_version, compare_versions),
(parse_version_string, parse_version_number): Add.
--
t-support header was not a good place for this. It should
go into a library e.g. gpgrt in the future. For now we
can keep it close to where it is needed.
* t-config-opt.in.json,
t-config-opt.out.json,
t-import.in.json,
t-import.out.json,
t-sign.in.json,
t-sign.out.json: New.
--
These should actually have been in a previous commit as
they are already registered.
* tests/json/t-json.c (test_contains): Try all siblings of
the haystack child.
--
This fixes the case where we don't match against the
first child because the order might have changed or
a new element was inserted at the top. Then we
have to try out also all the siblings.
* t-json.c (tests): Register new tests.
* t-createkey.in.json,
t-createkey.out.json,
t-decrypt-verify.in.json,
t-decrypt-verify.out.json,
t-decrypt.in.json,
t-decrypt.out.json,
t-delete.in.json,
t-delete.out.json,
t-encrypt-sign.in.json,
t-encrypt-sign.out.json,
t-encrypt.in.json,
t-encrypt.out.json,
t-export-secret-info.in.json,
t-export-secret-info.out.json,
t-export.in.json,
t-export.out.json,
t-json.c,
t-keylist-secret.in.json,
t-keylist-secret.out.json,
t-keylist.in.json,
t-keylist.out.json,
t-verify.in.json,
t-verify.out.json,
t-version.in.json,
t-version.out.json: New.
--
Except for help and getmore there is now a test for each command.
* tests/json/t-json.c (test_contains): When searching for "*" accept
every string.
--
This allows it to write tests that check for the existence of
a string value but don't care about the contents. E.g. for Data.
* tests/json/t-json.c (main): Skip if version is not at least
2.2.0
--
In the past new tests often failed when a modern GPGME was
used with old GnuPG's.
This should avoid the hassle for packagers without the
requirement that we test against old versions.
* t-support.h (parse_version_number, parse_version_string)
(compare_versions): New. Copy&Paste from src/version.c
(check_gpg_version): New helper to check for a gpg version.
--
This should make it easier to write tests that e.g.
rely on modern gnupg features.
* configure.ac: Configure makefile.
* tests/Makefile.am: Run json tests if gpg tests are run.
* tests/json/t-json.c: New testrunner for json tests.
* tests/json/t-config.in, tests/json/t-config.out: First test.
--
The idea of this test runner is that it only looks for parts
in the output. This should allow it to write robust tests
that check for the basics in the output but don't fail when
the output is extended or slightly changed.
* src/context.h (gpgme_context): Extend with trust_model.
* src/engine-gpg.c (engine_gpg): Extend with trust_model.
(gpg_set_engine_flags): Take trust_model from context.
(build_argv): Handle trust_model.
(gpg_release): Free trust_model.
* src/gpgme.c (gpgme_set_ctx_flag): Handle trust-model flag.
(gpgme_release): Release trust-model.
* doc/gpgme.texi: Document new flag for gpgme_set_ctx_flag.
(Context Flags): New subsection for the context flags.
* tests/run-keylist.c (show_usage, main): Add new --trust-model
parameter.
--
This gives a GPGME user fine grained control over the
trust-model.
Changing the trust model for only a single application depends
on:
GnuPG-Bug-Id: T4134
Maniphest Tasks: T4134
Differential Revision: https://dev.gnupg.org/D466
* lang/python/tests/Makefile.am,
lang/qt/tests/Makefile.am,
tests/Makefile.am,
tests/gpg/Makefile.am,
tests/gpgsm/Makefile.am,
tests/opassuan/Makefile.am (GNUPGHOME): Make variable explict.
--
If the build directory has too long path, gpgme could fail.
This is similar to
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=847206
In order to fix that, this patch extracts the GNUPGHOME variable
to be presented directly in the Makefile and thus overridable by
command line option.
A build system can then create a symlink to the GNUPGHOME directory
in /tmp and use that symlink as the GNUPGHOME directory
thus making the path very short.
GnuPG-Bug-Id: T4091
Patch provided by vlmarek
* src/engine-gpg.c (engine_gpg): Add diagnostics member.
(gpg_release): Release diagnostics data.
(gpg_new): Set up logger-fd and diagnostics.
(gpg_getauditlog): New. Copy diagnostics to a user data.
(engine_ops): Add getauditlog.
* src/engine-gpgsm.c (gpgsm_getauditlog): Return not implemented
for GPGME_AUDITLOG_DIAG.
* src/getauditlog.c (getauditlog_start): Don't reset engine
for diagnostics.
* src/gpgme.h.in (GPGME_AUDITLOG_DIAG): New.
(GPGME_AUDITLOG_DEFAULT): New alias to 0.
* tests/run-decrypt.c (show_usage, main): Add --diagnostics.
* doc/gpgme.texi(Additional Logs): Document getauditlog.
--
This enables users of GPGME to get more verbose information
from gpg which can assist users in figuring out a problem
that was before hidden behind a generalized error like
"Decryption Failed".
For GPGSM it is not yet available as it is problematic to
get it properly in server mode and GPGSM already had the
original audit log mechanism in place.
GPGME_AUDITLOG_DEFAULT was added for a more explicit
documentation.
* src/gpgme.h.in (_gpgme_op_decrypt_result): Add flag
legacy_cipher_nomdc.
* src/decrypt.c (parse_status_error): Set this flag.
* tests/run-decrypt.c (print_result): print it.
(main): Print the result even on error.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tests/gpg/t-verify.c (check_result): Tweak for gnupg < 2.2.7.
--
The not yet releases 2.2.7-beta may print a full fingerprint in the
ERRSIG status. This is compliant with the dscription but the new
t-verify test case did not took in account that older GnuPG versions
print only a keyid.
Fixes-commit: b99502274a
GnUPG-bug-id: 3920
Signed-off-by: Werner Koch <wk@gnupg.org>
* src/op-support.c (_gpgme_parse_plaintext): Add arg r_mime.
* src/decrypt.c (_gpgme_decrypt_status_handler): Ser mime flag.
* src/verify.c (_gpgme_verify_status_handler): Ditto.
* src/gpgme.h.in (gpgme_op_verify_result_t): Append fields 'is_mime'
and '_unused'.
(gpgme_op_decrypt_result_t): New field 'is_mime'. Shrink '_unused'.
* tests/run-decrypt.c (print_result): Print MIME flag.
* tests/run-verify.c (print_result): Ditto.
--
Note that this flag (Liternal Data packet's 'm' mode) is only
specified in RFC-4880bis. To use it you currently need to add
"rfc4880bis" to the the gpg.conf.
Signed-off-by: Werner Koch <wk@gnupg.org>
* src/gpgme.h.in (gpgme_op_encrypt_ext_start) New.
(gpgme_op_encrypt_ext): New.
(gpgme_op_encrypt_sign_ext_start): New.
(gpgme_op_encrypt_sign_ext): New.
* src/libgpgme.vers, tests/run-encrypt.c: Add them.
* src/encrypt.c (encrypt_start): Add arg recpstring.
(gpgme_op_encrypt): Factor code out to ...
(gpgme_op_encrypt_ext): new function with new arg recpstring.
(gpgme_op_encrypt_start): Factor code out to ...
(gpgme_op_encrypt_ext_start): new function with new arg recpstring.
* src/encrypt-sign.c (encrypt_sign_start): Add arg recpstring.
(gpgme_op_encrypt_sign): Factor code out to ...
(gpgme_op_encrypt_sign_ext): new function with new arg recpstring.
(gpgme_op_encrypt_sign_start): Factor code out to ...
(gpgme_op_encrypt_sign_ext_start): new function with new arg
recpstring.
* src/engine-backend.h (struct engine_ops): Change fields encrypt and
encrypt_sign.
* src/engine.c (_gpgme_engine_op_encrypt): Add arg recpstring and pass
to engine.
(_gpgme_engine_op_encrypt_sign): Ditto.
* src/engine-gpg.c (append_args_from_recipients_string): New.
(gpg_encrypt): Add arg recpstring and call new function as needed.
(gpg_encrypt_sign): Ditto.
* src/engine-gpgsm.c (set_recipients_from_string): New.
(gpgsm_encrypt): Add arg recpstring and call new function as needed.
* src/engine-uiserver.c (set_recipients_from_string): New.
(uiserver_encrypt): Add arg recpstring and call new function as
needed.
* tests/run-encrypt.c (xstrdup): New.
(main): Add option --keystring.
* src/gpgme-json.c (get_keys): Simplify.
(op_encrypt): Modify to make use of the extended encrypt function.
--
This new feature can be used to avoid the need for a key lookup and
thus several extra calls to the backend.
Note that run-test uses a semicolon as delimiter because that make
testing the feature on the command line much easier.
Signed-off-by: Werner Koch <wk@gnupg.org>
* src/op-support.c (_gpgme_parse_failure): Ignore failures with
location "gpg-exit".
* tests/gpg/t-verify.c (main): Adjust for the now working checking of
the second key.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tests/gpg/t-verify.c (PGM): New. Use it instead of __FILE__.
(test_sig1_plus_unknown_key): New test signature.
(check_result): Allow checking of several signatures.
(main): Check a signature with a know and an unknown key.
Signed-off-by: Werner Koch <wk@gnupg.org>
* src/gpgme.h.in (gpgme_import_result_t): Extend with skipped_v3_keys.
* src/import.c (gpgme_op_import_result): Extend debug with new field.
(parse_import_res): Parse skipped_v3_keys.
* tests/gpg/t-support.h, tests/run-support.h (print_import_result):
Print skipped_v3_keys.
--
This makes it possible to handle this in a GUI in a future
version.
GnuPG-Bug-Id: T3776
* tests/gpg/Makefile.am: Don't allow target with '/'.
* tests/gpgsm/Makefile.am: Ditto.
--
BSD Make doesn't allow a target with '/'. We still have such a target
in lang/python/Makefile.am, but it's for maintainer only, so,
assumption to GNU Make is OK there.
Signed-off-by: NIIBE Yutaka <gniibe@fsij.org>
* tests/gpg/Makefile.am, tests/gpgsm/Makefile.am: Remove ./.
--
GNU Make is powerful enough for handling and interpreting of
pathname as target, but BSD Make is not.
GnuPG-bug-id: 3056
Signed-off-by: NIIBE Yutaka <gniibe@fsij.org>
* src/data.c (_gpgme_data_new): Check for failed selftest.
* tests/run-support.h (make_filename): Print a message on mallooc
failure.
(init_gpgme_basic): New.
* tests/run-identify.c (main): Call init_gpgme_basic becuase we do not
need to setup a protocol.
* tests/t-data.c: Define PGM and include run-support.h.
(make_filename): Remove.
(main): Call init_gpgme_basic.
--
Note: This patch may break applications which used gpgme_data but no
gpgme_new without having called the required gpgme_check_version.
GPGME can be used without a protocol for example to work with the data
object abstraction. Thus a call to gpgme_data_new also needs to check
the result of the core selftests - including on whether
gpgme_check_version has been called.
Signed-off-by: Werner Koch <wk@gnupg.org>
* tests/gpgsm/Makefile.am (GPG_AGENT): Set var. It is used later.
--
Note that the var is used by the gpgsm.conf target.
Reported-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Werner Koch <wk@gnupg.org>
* lang/python/tests/Makefile.am: Distinguish target and path.
* tests/gpg/Makefile.am: Ditto.
* tests/gpgsm/Makefile.am: Ditto.
--
GNU Make is powerful enough to match path to target (and vice versa),
but BSD make is not.
GnuPG-bug-id: 3056
Signed-off-by: NIIBE Yutaka <gniibe@fsij.org>
* src/gpgme.c (gpgme_set_ctx_flag, gpgme_get_ctx_flag): New flag
"auto-key-retrieve".
* src/context.h (gpgme_context): New field auto_key_retrieve.
* src/engine-backend.h (struct engine_ops): Add arg auto_key_retrieve
to field 'decrypt'.
* src/engine-gpg.c (gpg_decrypt): Add arg auto_key_retrieve and pass
option --auto-key-retrieve to gpg. Adjust all callers.
(gpg_verify): Ditto.
* src/engine-gpgsm.c (gpgsm_decrypt): Add dummy arg auto_key_retrieve.
* src/engine-uiserver.c (uiserver_decrypt): Ditto.
* tests/run-verify.c (main): Add option --auto-key-retrieve.
--
This makes the --auto-key-retrieve option available in the GPGME API.
Test plan:
Run
GPGME_DEBUG=9:out tests/run-verify SIGNEDFILE
with and without its new option --auto-key-retrieve and check in the
trace stored in "out" whether --auto-key-retrieve was passed to gpg.
Signed-off-by: Werner Koch <wk@gnupg.org>
